Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 58

Страница: 58 / 132

Page 40

ODF Speed Facer Operating Manual

IGURE

4-1. S

TANDARD

CONFIGURATION

(ODF80

SHOWN

)

WARNING

Do not configure or adjust the machining direction
unless the machine is turned off, the air or
hydraulic hose has been disconnected, and any
required lockout/tag out has been performed.

To configure the ODF Speed Facer for machining a face
on a flat flange, complete the following steps:

1. Assemble the ODF Speed Facer on the work-

piece (see Section 3. on page 30).

2. Complete all pre-operation checks (see

Section 4.1).

3. Loosen both the radial and axial gib lock

screws.

IGURE

4-2. G

LOCK

SCREWS

4. Use a 3/8" ratchet driver on the radial and axial

feed screws to position the cutting tool to the
starting point of the cut.

5. Hand tighten only the axial gib lock screw.
6. Set the feed direction knob (shown in Figure 4-7

on page 43) to the desired direction.

7. Set the feed rate, referencing Section 3.4.7 on

page 37 and using the feed adjustment screw on
the feed box.

4.2.2

Configuring for a counterbore

Do the following to configure the machine for a coun-
terbore:

1. Assemble the ODF Speed Facer on the work-

piece (see Section 3. on page 30).

2. Complete all pre-operation checks (see

Section 4.1).

3. Reposition the feed box from the radial feed

screw to the axial feed screw, securing it with
the two screws.

4. Loosen both the axial and radial gib lock

screws.

5. Use a 3/8" (9.5 mm) ratchet driver on the radial

and axial feed screws to position the cutting
tool to the starting point of the cut.

6. Hand tighten only the radial gib lock screw.
7. Set the feed direction knob to the desired posi-

tion. See Section 3.4.7 on page 37.

RADIAL GIB

LOCK SCREW

Содержание H&S TOOL SPEED FACER ODF100





































































































































Результаты поиска

Содержание H&S TOOL SPEED FACER ODF100

Отзывы:

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренды по названию

Популярные бренды

Climax H&S TOOL SPEED FACER ODF100, Руководство по эксплуатации

Результаты поиска

Содержание H&S TOOL SPEED FACER ODF100

Отзывы:

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренды по названию

Популярные бренды