manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Руководство по эксплуатации

Поделиться
Скачать
Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 56

Page 38

ODF Speed Facer Operating Manual

For example, when the motor is installed on the top, 
the red hose connects to the red motor port.

Do the following to install the drive motor:

1. Check that the drive key is present in the slot of 

the motor shaft. 

2. Fit the motor drive shaft into the drive hub, 

aligning the drive key with the slot in the drive 
hub.

3. Tighten the two screws on the mounting collar 

to secure. 

3.4.9

Connecting the Air Caddy

Connect the Air Caddy to the machine using the air hose 
disconnect on the speed adjustment valve. 
Refer to Figure 2-3 on page 12 for a description of the 
Air Caddy.

CAUTION

Always lockout or disconnect the air supply before 
making machine or tool adjustments. Always use 
the Start and E-Stop power buttons on the Air Caddy 
to start and stop the machine instead of using the 
speed adjustment valve.

3.4.10

Installing the hydraulic motor

NOTICE

Pay careful attention to the machine direction and 
hose connections. If the machine is run opposite to 
the rotation direction, the feed tripper may be 
damaged. The correct direction is clockwise when 
viewed from above the bridge. 

Do the following to install the drive motor: 

1. Check that the drive key is present in the slot of 

the motor shaft.

2. Fit the hydraulic shaft adapter into the drive 

hub, aligning the drive key with the slot in the 
drive hub.

3. Tighten the two screws on the mounting collar 

to secure.

3.4.11

Connecting the HPU (hydraulic 
power unit)

Reference the included HPU (hydraulic power unit) 
operating instructions for information on connecting the 
hydraulic motor to the HPU and the power source to the 
HPU. 
If the HPU is not being supplied as part of the rental or 
sale of this machine, read and throughly understand the 
instructions for the HPU being used.

F

IGURE

 3-14. I

NSTALLED

 

AIR

 

MOTOR

 

DRIVE

F

IGURE

 3-15. I

NSTALLED

 

HYDRAULIC

 

MOTOR

 

DRIVE

 (

BOTTOM

 

SIDE

)

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды