manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Руководство по эксплуатации

Поделиться
Скачать
Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 68

Page 50

ODF Speed Facer Operating Manual

4. Loosen the jam nut and unscrew the adjusting 

bolt to free the cable from the feedbox. 

5. Loosen the Velcro straps to free the protective 

cable conduit, remove and put aside.

Do the following on the trip actuator:

1. Remove the cover plate.
2. Lift the barrel end of the cable up and out of 

the trip arm and the cable out of the slot in the 
actuator block.

F

IGURE

 5-8. B

ARREL

 

END

 

OF

 

CABLE

 

REMOVAL

 (

LEFT

); C

ABLE

 

AND

 

HOUSING

 

CUT

-

TERS

 (

RIGHT

)

5.3.9.2

Cable preparation

Do the following to prepare the cable:

1. The use of a cable and jacket cutter is sug-

gested (ParkTool #CN-10).

2. Cut only the cable jacket to the following 

length according to the ODF Speed Facer model: 
•

ODF30: 22" (55.8 cm)

•

ODF40: 30.5" (77.5 cm)

•

ODF50: 38.5" (97.8 cm) 

•

ODF60: 38.5" (978 mm)

•

ODF70: 44" (1,118 mm)

•

ODF80 and larger: and 60" (1,524 mm)

T

IP

:

Even with the use of a cable and jacket cutter, 
pinching of the internal jacket may occur. If it 
does, ream out with an awl or scribe before 
installing the cable. Install ferrules on both 
ends of the cable jacket by crimping. 

3. Thread the spring onto the cable and up against 

the barrel end.

4. Thread the cable through the cable jacket.

F

IGURE

 5-9. B

ARREL

 

END

 

OF

 

CABLE

 

WITH

 

SPRING

, 

FERRULE

 

INSTALLED

 

ON

 

CABLE

 

HOUSING

 (

LEFT

); 

CABLE

 

INSTALLED

 

IN

 

ACTUATOR

 

HOUSING

 

(

RIGHT

)

5.3.9.3

Cable installation

To install the cable, do the following on the trip actua-
tor (see Figure 5-9-right): 

1. Install the barrel end of the cable into the 

pocket on the trip arm.

2. Trap the spring between the trip arm and the 

actuator body. 

3. Insert the cable into the slot of the actuator 

body. 

4. Reinstall the protective cable conduit over the 

trip cable. 

Do the following on the feedbox:

1. Thread the cable free cable end through the 

90° elbow, adjusting bolt and jam nut. 

2. Screw the jam nut onto the adjusting bolt.
3. Set the adjusting bolt approximately halfway 

into the feedbox housing. 

4. To determine the final length of the cable, take 

up the slack until the trip actuator arm is 90° to 
the trip actuator body. Trim the cable even with 
the far side of the feedbox wall.

F

IGURE

 5-10. 90° 

ELBOW

, 

ADJUSTING

 

NUT

 

AND

 

JAM

 

NUT

 (

LEFT

); 

CABLE

 

END

 

SHOWN

 

AT

 

TRIMMING

 

LOCATION

 (

RIGHT

)

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды