Clifford CLIFFORD 50.7X страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 64

background image

18

© 2008 Directed Electronics. All rights reserved.

(+) Positive Light Flash Output

(-) Negative Light Flash Output

WHITE H1/11

(+) LIGHT FLASH OUTPUT

WHITE H1/11

(-) LIGHT FLASH OUTPUT

Note:

For parking light circuits that draw 10-amps or more, the internal jumper

must be switched to a (-) light flash output. (See Setting the light flash polarity

section of this guide.) P/N 8617 or a standard automotive SPDT relay must be

used on the H1/11 light flash output harness wire.

H1/12

ORANGE

(-) 500mA GROUND WHEN ARMED OUTPUT

This wire supplies a (-)500 mA ground as long as the system is armed. This

output ceases as soon as the system is disarmed. The GWA can be hooked up

to a window module, a voice module or any accessory that requires a ground

when armed.

➢

Auxiliary harness (H2)

H2/1

LIGHT GREEN/BLACK

(-) 200mA FACTORY ALARM DISARM OUTPUT

This wire sends a negative pulse every time the remote start is activated , trunk

release is activated (programmable on/off) or when the doors are unlocked with

the remote. This can be used to pulse the disarm wire of the vehicle’s factory anti-

theft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown

in the following diagrams.

«
...
16
17
18
19
20
...
»

Содержание CLIFFORD 50.7X

































































Отзывы:

Нет отзывов

Похожие инструкции для CLIFFORD 50.7X

Бренд: Ohsung Electronics Страницы: 18

Бренд: jablotron Страницы: 2

Бренд: Yaber Страницы: 52

Бренд: jablotron Страницы: 2

Бренд: ALLEN & HEATH Страницы: 15

Бренд: Radio Shack Страницы: 29

Бренд: Directed Electronics Страницы: 56

Бренд: AXIL Страницы: 123

Бренд: Viper Страницы: 4

Бренд: Manfrotto Страницы: 3

Бренд: Universal Страницы: 19

Бренд: Pluggit Страницы: 44

Бренд: XAG Страницы: 12

Omegalink OL-RS-VW1

Бренд: ADS Страницы: 12

Бренд: ADS Страницы: 22

Бренд: Big Button Страницы: 11

Бренд: Gianni Industries Страницы: 3

Бренд: HeatTrak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды