Clifford CLIFFORD 50.7X страница 38 Скачать руководство пользователя

Страница: 38 / 64

For more information about the remote control functions, see the Owners

Guide.

Button

Level

Direct

Access

A U

x 1

A U

x 2

A U

x 3

A U

x 4

A U

ARM/LOCK

(Panic)

SILENT ARM

SENSOR

BYPASS

SILENT ALARM

SENSORS

SILENT ALARM

ALL ZONES

A U

DISARM/UN-

LOCK (Panic)

SILENT DISARM

VALET ON/OFF

CAR FINDER

A U

STARTER

ON/OFF

RESET RUNTIME

TIMER MODE

ON/OFF

SMART START

ON/OFF

DEFOGGER ON

A U

TRUNK

RELEASE (Red/

White)

AUX 1

AUX 2

AUX 3

A U

Advance Level

Change Car

(3s) Enter

programming

(8s)

CABIN

TEMPERATURE

REQUEST

RUNTIME

CHECK

EVENT HISTORY

REPORT

Important:

To access “Cabin temperature request, Runtime

check and event report history, press the

AUX

button the speci-

fied amount of times, and then hold.

System features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to

access and change any of the feature settings using the Valet/program switch.

However, this process can be simplified by using the Bitwriter®. Any of the

settings can be changed and then assigned to one of four remote controls. This

feature is called Owner Recognition. Each time that particular remote control is

used to disarm the system, the assigned feature settings are recalled. Owner

Recognition is only possible when programming the unit via the Bitwriter®.

If programming with the Bitwriter®, the learn routine can be locked or

unlocked. If the learn routine has previously been locked, it must be

unlocked with Bitwriter® - this cannot be done manually with the Valet

switch.

Содержание CLIFFORD 50.7X
































































Результаты поиска

Содержание CLIFFORD 50.7X

Отзывы:

Похожие инструкции для CLIFFORD 50.7X

Бренды по названию

Популярные бренды

Clifford CLIFFORD 50.7X, Руководство по установке

Результаты поиска

Содержание CLIFFORD 50.7X

Отзывы:

Похожие инструкции для CLIFFORD 50.7X

Бренды по названию

Популярные бренды