Clifford CLIFFORD 50.7X страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 64

background image

25

© 2008 Directed Electronics. All rights reserved.

5

BLUE/WHITE

(-) 200 mA 2ND STATUS/REAR DEFOGGER

This wire supplies a 200mA output as soon as the module begins the remote

start process. The Blue/White wire can also be used to activate the defogger

trigger (latched/pulsed) 10-seconds after the remote start engages. (See the

Feature Descriptions, Menu#3, feature #11 for details about programming this

output).

➢

Remote start auxiliary output, 5-pin

These signals are provided to drive additional optional relays.

1

PINK/WHITE

(-) 200mA FLEX RELAY CONTROL OUTPUT

This wire is programmed as (-) 2nd ignition output from factory and can be pro-

grammed (to drive a relay) as a (-) starter or an accessory output.

2

ORANGE

(-) 200mA ACCESSORY OUTPUT

This wire works like the main accessory wire and can be used (with a relay) to

drive any additional accessory circuits in the vehicle.

3

VIOLET

(-) 200mA STARTER OUTPUT

This wire works like the starter wire and can be used (with a relay) to drive any

additional starter circuits in the vehicle.

4

PINK

(-) 200mA IGNITION 1 OUTPUT

This wire works like the ignition 1 wire and can be used (with a relay) to drive

any additional ignition circuits in the vehicle.

Note:

Wires 1 - 4 on the remote start auxiliary outputs are wired to the (-) triggers

for the onboard remote start relays and are not diode isolated. If connecting

these wires directly to the vehicle you must place a 1-amp diode in line to pre-

vent feedback from the vehicle.

«
...
23
24
25
26
27
...
»

Содержание CLIFFORD 50.7X

































































Отзывы:

Нет отзывов

Похожие инструкции для CLIFFORD 50.7X

Бренд: Vector Страницы: 12

Бренд: Hunter Страницы: 2

Бренд: Absima Страницы: 42

Бренд: Paradise Datacom Страницы: 48

Бренд: FUTABA Страницы: 16

Бренд: Everflourish Страницы: 3

Бренд: Vtronix Страницы: 8

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 19

Бренд: Sony Страницы: 18

Бренд: Sony Страницы: 23

RM-AX4000 - Integrated Remote Commander

Бренд: Sony Страницы: 20

RM-AX1400 - Home Theater Remote Control

Бренд: Sony Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды