manualshive.com logo in svg

CleaverBrooks Hawk 1000, Руководство по эксплуатации

Поделиться
Скачать
CleaverBrooks Hawk 1000 Скачать руководство пользователя страница 49

Hawk 1000

Section 4 — System Configuration

Part No. 750-366

4-19

Figure 4-17. VFD screen

Variable Frequency Drive for Combustion Air Fan Motor

 

Variable frequency drives (VFDs) offer many benefits to reduce energy costs and extend the life of mechanical 
equipment.

The optional Variable Frequency Drive (VFD; see Figure 2-7) controls the speed of the combustion air fan 
motor for the purposes of improving boiler efficiency and reducing electrical energy consumption.

4.4.8  Options

Oxygen Analyzer

The Oxygen (O2) Analyzer (See Figure 2-8) is available for monitoring stack flue gas oxygen concentration. The 
O2 Analyzer transmits an analog signal to the controller. The O2 signal is used for Low O2 alarms, Low O2 
Shutdown and in calculating boiler efficiency. O2 concentration is displayed on the Boiler Overview and Firing 
Rate screens.

Figure 4-18. O2 Analyzer

Содержание Hawk 1000



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды