Clear-Com Tempest2400 Скачать руководство пользователя страница 60

Страница: 60 / 102

www.clearcom.com

Remote Transceiver

Setup the Transceiver

•

Choose a BaseStation location.

•

Choose a Transceiver location.

•

Choose an antenna configuration.

•

Install CAT-5 cable and connect to the BaseStation and Transceiver.

•

Confirm operation by observing the Transceiver LEDs.

The Tempest Remote Transceiver is an optional accessory that allows antennas to be located up to 1,500 feet away from

the BaseStation without the RF signal loss that is associated with using long runs of coaxial cable.

The Tempest Remote Transceiver connects to the rear of the BaseStation with standard CAT-5 wiring with RJ-45 connectors.

Note that there are two RJ-45 connectors on the back of the BaseStation and they are not interchangeable. The second

RJ-45 is for a LAN connection.

Install the BaseStation in a convenient location.

Install CAT-5 cable so that it is protected from electronic interference as much as possible.

Install the Transceiver and antennas in a location that provides the best RF coverage.

Connect the CAT-5 cable to the BaseStation and the Transceiver.

When the BaseStation detects the presence of the Transceiver, there is a brief automatic configuration process

before the Transceiver takes over the radio function from the BaseStation.

There are two RP-TNC antenna connectors on the top of the

transceiver allowing for connection of two half wave antennas

or alternate antenna configurations. Always ensure that two

antennas are securely connected for proper system operation.

The Transceiver antenna connectors are

made to be water resistant, so outdoor use

is acceptable. The cable connections on the

bottom of the transceiver are not water tight,

so always protect from immersion. In severely

blowing rain it may be prudent to protect with

an RF transparent cover such as a Ziploc bag.

Coaxial cable may be used to connect alternative

antenna options.

See the Antenna Configuration section.

Pairs of Directional Antennas must

be aimed to cover the same area

Содержание Tempest2400







































































































Результаты поиска

Содержание Tempest2400

Отзывы:

Похожие инструкции для Tempest2400

Бренды по названию

Популярные бренды

Clear-Com Tempest2400, Справочное руководство

Результаты поиска

Содержание Tempest2400

Отзывы:

Похожие инструкции для Tempest2400

Бренды по названию

Популярные бренды