23
EN
■
Do not iron across zippers, rivets, buckles etc. to avoid scratches on the coating of
the soleplate.
■
Only open the water tank cap to
fi
ll the water tank. Otherwise keep the cap closed
during operation.
■
Always place the device on a level, stable base.
■
During and shortly after use, place the device on the storage tray or on the support
foot and on a level, stable, heat and moisture-resistant base.
It is possible that a mild odour is produced the
fi
rst time you use the device. This
is harmless and will cease as you use the device.
Filling the water tank
ATTENTION!
■
Scalding hazard due to hot steam!
Let the device cool off before opening the water
tank.
■
Always pull the mains plug before the water tank is re
fi
lled / emptied. Never pull on
the mains cord, but always on the mains plug.
■
Never
fi
ll the water tank with additives. The device could be destroyed and safe op-
eration of the device can no longer be assured.
■
Never exceed the maximum level.
The water tank (
7
) must be
fi
lled for steam ironing. This is omitted when dry ironing.
1. Make sure that the device is
not
connected to the mains supply. Set the On/Off switch
for the heat function of the water tank (
A
) to position
0
(steam production off) and the
temperature control (
2
) to position
0
(turn
0
to the mark (on the temperature control
light
3
)).
2. Turn the water tank cap (
D
) open.
3. Fill the water tank (
7
) with distilled water. It holds approx.
500 ml. Use the measuring cup to
fi
ll it.
4. Firmly turn the water tank cap (
D
) until tight.
Heating up the iron
1. Check the label on the article of clothing for the required ironing temperature (see
chapter “Ironing recommendations”) and set it with the temperature control (
2
).
2. Set the On/Off switch for the heat function of the water tank (
A
) to position
0
(steam
emission off).
3. If you haven’t already done so, place the device on the ironing board or a stable,
level, heat and moisture-resistant base.
4. Place the iron on the storage tray (
8
).
5. Insert the mains plug in a properly installed socket that is easily accessible.
6. Set the On/Off switch for the heat function of the soleplate (
C
) to position
I
(soleplate
on).
D
01175_DE-EN-FR-NL_A5_V1.indb 23
01175_DE-EN-FR-NL_A5_V1.indb 23
17.01.2017 16:09:08
17.01.2017 16:09:08
Содержание Z 01175
Страница 2: ...01175_DE EN FR NL_A5_V1 indb 2 01175_DE EN FR NL_A5_V1 indb 2 17 01 2017 16 08 59 17 01 2017 16 08 59...
Страница 54: ...01175_DE EN FR NL_A5_V1 indb 54 01175_DE EN FR NL_A5_V1 indb 54 17 01 2017 16 09 21 17 01 2017 16 09 21...
Страница 55: ...01175_DE EN FR NL_A5_V1 indb 55 01175_DE EN FR NL_A5_V1 indb 55 17 01 2017 16 09 21 17 01 2017 16 09 21...
Страница 56: ...01175_DE EN FR NL_A5_V1 indb 56 01175_DE EN FR NL_A5_V1 indb 56 17 01 2017 16 09 21 17 01 2017 16 09 21...
