manualshive.com logo in svg

Clarke WOODWORKER 6460015, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke WOODWORKER 6460015 Скачать руководство пользователя страница 13

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ASSEMBLY

STAND ASSEMBLY

1. Ensure the blade is retracted 

inside the machine by turning the 
height adjuster. Turn the machine 
upside down, ideally on a soft 
surface.

2. Fix the dust extract duct 

connector to the motor housing 
with 4 x bolts using a 7mm flat or 
ring spanner.

3. Bolt the 4 x legs to the table using 

bolts/nuts/2 x washers. Only 
assemble finger tight at this stage.

• The leg with the aperture for 

the On/Off switch assembly 
must be mounted on the left 
side when facing the blade 
height adjuster.

4. Add the long and short 

crossbeams to the legs using 
further bolts/nuts/washers. Only 
assemble finger tight at this stage.

5. Pass the On/Off switch (attached 

to its cable), though the aperture 
in the front leg and install in 
position with the 2 self-tapping 
screws.

Содержание WOODWORKER 6460015

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды