Clarke Contractor CTS12 Скачать руководство пользователя страница 26

Страница: 26 / 32

TROUBLE SHOOTING

TROUBLE

PROBABLE CAUSE

REMEDY

Saw will not start

1. Saw not plugged in

1. Plug in the machine

2. Fuse blown or circuit breaker

2. Replace fuse or reset circuit

tripped

breaker

3. Power cable damaged

3. Have cable replaced by

authorised service centre

Does not make

1. Positive stops not adjusted

1. Check blade with square and

accurate 45

and 90

correctly adjust positive stops

Rip Cuts

and adjust pointer to zero

Material Pinches

1. Rip fence not aligned with blade

1. Check and adjust rip fence

Blade When Ripping

2. Warped wood, edge against

2. Select another piece of wood

fence not straight

Material binds on

1. Riving knife not aligned correctly

1. Check and align Riving knife with

Riving Knife

with blade

blade

Saw makes

1. Dull blade

1. Replace blade

unsatisfactory cuts

2. Blade mounted backwards

2. Turn blade around

3. Gum or pitch on blade

3. Remove blade and clean with

turpentine and coarse steel wool

4. Incorrect blade for work

4. Change the blade

5. Gum or pitch on table causing

5. Clean table with turpentine and

erratic feed

steel wool and apply wax

Material kicked back

1. Rip fence out of alignment

1. Align rip fence with blade

from blade slot

2. Riving knife not aligned with blade

2. Align Riving knife with blade

3. Feeding stock without rip fence

3. Install and use rip fence

4. Riving knife not in place

4. Install and use Riving knife with

guard

5. Letting go of material before it is

5. Push material all the way past

all the way past the saw blade

blade before releasing work

6. Dull blade

6. Replace blade

7. Mitre angle lock knob is not tight

7. Tighten knob

Blade does not raise

1. Sawdust and dirt in raising and

1. Brush or blow out loose dust

or tilt freely

tilting mechanism

and dirt

Blade does not come

1. Extension cable too light or too

1. Replace with adequate size

up to speed

long

cable

2. Low voltage

2. Contact your electric company

Machine vibrates

1. Saw not mounted securely to

1. Tighten all mounting hardware

Stand or work bench

2. Stand or bench on uneven floor

2. Reposition on flat level surface

Fasten to floor if necessary

3. Damaged saw blade

3. Replace blade

Does not make

1. Mitre gauge out of adjustment

1. Adjust mitre gauge

accurate 45

and

crosscuts

Содержание Contractor CTS12

































Результаты поиска

Содержание Contractor CTS12

Отзывы:

Бренды по названию

Популярные бренды

Clarke Contractor CTS12, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Contractor CTS12

Отзывы:

Бренды по названию

Популярные бренды