Clarke 6460120 Скачать руководство пользователя страница 23

Страница: 23 / 23

Specifications

Part No ........................................................................... 6460120

Motor ............................................................................. 230V, 50Hz, 1Ph

Speed ............................................................................ 1420RPM

Power Rating ................................................................. 370Watts

Running Current ............................................................ 4.3Amps

Fuse Rating .................................................................... 13Amps

Blade Size ...................................................................... 1650mmx0.5”x0.65mm - 10tpi

Blade Speed ................................................................. 110/160 ft/min.

Cutting Capacity at 90

.......... Round ........................ 170mm Dia.

Rectangular .............. 190mm wide* (see chart below)

................................... 170mm Deep** (see chart below)

Cutting Capacity at 45

Round ........................ 85mm Dia.

Rectangular .............. 85x60mm deep, max

Angle Cut ...................................................................... 0 - 45 Degrees

Weight ............................................................................ 76.5kg net

Noise Level .................................................................... less than 78dB (Sound Power

Cutting
capacity
at 90

Level) Whilst Cutting

Please contact your nearest dealer, or CLARKE International, as follows:

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

Parts & Service contacts

CLARKE CUTTING OIL

Part No.

1 Litres 3051059

5 Litres 3051061

Available from your Clarke
dealer.

Max. Distance between Guides

Distance between Bed and Frame

To determine whether or not the saw will cut a piece of
a certain size, consult the chart.
e.g. the saw will cut a piece 160mm wide x 100mm
deep, but NOT 180mm wide x 100mm deep.

Содержание 6460120























Результаты поиска

Содержание 6460120

Отзывы:

Похожие инструкции для 6460120

Бренды по названию

Популярные бренды

Clarke 6460120, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание 6460120

Отзывы:

Похожие инструкции для 6460120

Бренды по названию

Популярные бренды