manualshive.com logo in svg

CKD ABSODEX AX9000XS-U2, Инструкция по эксплуатации

Поделиться
Скачать
CKD ABSODEX AX9000XS-U2 Скачать руководство пользователя страница 39

4. Network Operation Mode

 

[SMF-2008-A] 

– 4-8 – 

4.2. Data Input Operation 

In a data input operation, ABSODEX is operated using reception data from the PLC. 
Consequently, the operation description of ABSODEX can be changed only by changing the 
communication data from the PLC. 
 

4.2.1.  Operation method 

 
i)  Switch the operation mode. 

Switch the operation mode to the “network operation mode”. 
The switching method can be performed by any of the following. 

  Send communication command “M7”. 

  Set PRM29 (mode when power is turned on) = 7 and restart the control power. 

  Switch using a command code (0021h). 

 

ii)  Switch to a table operation. 

Turn on the table operation and data input operation switching input (RY (n+1) 3). 
 

OFF 

: Table operation 

 

ON 

: Data input operation 

 

iii)  Setting of operation description 

Set the instruction, movement unit and movement speed unit. 
Then send values equivalent to the A code/P code and F code. 
 

iv) Start by data input operation 

The operation description set in iii) is executed by turning on the start input. 

 

 

 

Содержание ABSODEX AX9000XS-U2












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды