manualshive.com logo in svg

CKD ABSODEX AX9000XS-U2, Инструкция по эксплуатации

Поделиться
Скачать
CKD ABSODEX AX9000XS-U2 Скачать руководство пользователя страница 32

4. Network Operation Mode

 

[SMF-2008-A] 

– 4-1 – 

4.  Network Operation Mode 

The network operation mode is an operation mode which can be used for wiring saving 
specification-U2 (CC-Link). 
 

4.1. Point Table Operation 

The point table operation use point table data in the ABSODEX driver to operate. 
As for point table data, point table data can be referred to and set from the PLC. 
 
 

4.1.1.  Operation method 

 

i)  Set a point table. 

Set it using AX Tools Ver 2.10 or later or a command code. 
A command code can be used only in the network operation mode. 
 

ii)  Operation mode switching 

Switch the operation mode to the “network operation mode”. 
The switching method can be performed by any of the following. 

  Send communication command “M7”. 

  Set PRM29 (mode when power is turned on) = 7 and restart the control power. 

  Switch using a command code (0021h). 

 

iii)  Switch to a table operation. 

Turn off the table operation and data input operation switching input (RY (n+1) 3). 
 

OFF 

: Table operation 

 

ON 

: Data input operation 

 

iv) Selection of point table 

For selection, use a program number selection input (RYn0 to RYn5). 
The selection method is a method set in PRM36 (switching of I/O program number selection 
method). The selection range of a point table is 0 to 63. 
 

v)  Start of point table 

Execute the point table being selected by turning on the start input. 

 
 

 

Содержание ABSODEX AX9000XS-U2












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды