manualshive.com logo in svg

CKD ABSODEX AX9000XS-U2, Инструкция по эксплуатации

Поделиться
Скачать
CKD ABSODEX AX9000XS-U2 Скачать руководство пользователя страница 17

3. CC-Link Communication Function

 

[SMF-2008-A] 

– 3-4 – 

Table 3.6. Load command code (RWwn+2) list 

Code 

No.   

Item/Function 

Loaded data 

Loaded data 

designation 

RWwn+5 

RWrn+3 

RWrn+4 

0010h 

Current alarm 
loading 

Lower 8 bits: Alarm loading 1 
Upper 8 bits: Alarm loading 2 

Lower 8 bits: Alarm loading 3 
Upper 8 bits: Alarm loading 4 

- 

0020h 

Operation mode 
loading 

Current operation mode No. 

0 (fixed) 

- 

0025h 

Parameter 
loading 

Lower 16 bits of parameter 

set value 

Upper 16 bits of parameter 

set value 

Parameter 

number 

 
Load current alarm (0010h) 

The current alarm number is loaded. 
It is set as loaded data. Each byte indicates the type, and up to four alarms are specified. 
Alarm indication is consistent to the 7-segment LED indication. The first digit indicates details of 
the alarm and the second digit indicates the alarm number. Alarms not expressed in 0 to F 

Alarm H →"d" 

Alarm L →"b" 

Alarm P, U and others →"8" 

Alarms are set in the order from "F" to "0." 
In case of "no alarm," "00" is set. 

 
 

Operation mode loading (0020h) 

The current operation mode is loaded. 
The number of the operation mode is set in the loaded data. 

 

Table 3.7. Loadable operation mode list 

Operation mode 

Loaded data 

set value 

Automatic operation mode 

1 

Single block mode 

2 

MDI (manual data input) mode 

3 

Jog mode 

4 

Servo OFF mode 

5 

Pulse string input mode 

6 

Network operation mode 

7 

 

 
Parameter loading (0025h) 

The set value of the parameter designated with the parameter number (RWwn+5) is loaded using 
an integer value. 
A parameter with a decimal value is loaded using a value multiplied by 100 or 10,000. 
For details, refer to the “Parameter list” on page 3-6. 

 

 

 

Содержание ABSODEX AX9000XS-U2












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды