manualshive.com logo in svg

CKD ABSODEX AX9000XS-U2, Инструкция по эксплуатации

Поделиться
Скачать
CKD ABSODEX AX9000XS-U2 Скачать руководство пользователя страница 29

3. CC-Link Communication Function

 

[SMF-2008-A] 

– 3-16 – 

3.7.  LED Indication

 

The state of the module and that of the network can be displayed. See the description in the 
following table for the LED indication. 
 

 

Fig. 3.18. Name of LED 

 

Table 3.12. LED specification list 

Name of 

LED 

Color 

Description of indication 

SD 

Green 

Lit during data transmission. 

RD 

Lit during data reception. 

L RUN 

Lit when the slave station is receiving normal data from the master station. 

Unlit upon time-over. 

L ERR 

Red 

Unlit during normal communication. (L RUN is lit.) 

Lit upon a transmission error (CRC error). 
Lit upon an error in the station number setting or transmission speed setting. 
ERR blinks when the station number setting or transmission speed setting is 
changed in the middle. 

Unlit upon time-over. 

 
 
 

Table 3.13. LED state list 

LRUN 

LERR 

SD 

RD 

Operation 

 

◎

 

◎

 

 

CRC errors are sometimes caused in spite of normal updates. 

 

0.4s

◎

 

◎

 

 

The baud rate or station number setting is changed from the power-on setting. 

 

◎

 

 

 

Cannot respond due to a CRC error in the reception data. 

 

 

◎

 

 

Normal communication 

 

 

 

 

No data arrives at the own station. 

 

◎

 

◎

 

 

Response to polling is made though the refreshment reception is in a CRC 
error. 

 

◎

 

 

 

CRC error in data destined to own station 

 

 

◎

 

 

Link start is not made. 

 

 

 

 

There is no data destined to the own station or reception is disabled. 

 

 

 

 

Data reception is disabled. In shutdown or H/W resetting. 

 

 

 

/

 

Incorrect baud rate or station number setting 

: Lit, 

: Unlit, 

◎

: Blink 

 
The blinking rate of SD is too quick that you may feel that the LED is continuously lit in the 
communication state. 
 

 

 

 

 

 

 

 

 

Up 

L ERR 

L RUN 

RD

 

SD

 

Содержание ABSODEX AX9000XS-U2












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды