Civemasa STAC M 500 Скачать руководство пользователя страница 2

Страница: 2 / 45

Civemasa Implementos Agrícolas

STAC M 500

Introduction

The STAC M 500 plow was specially designed to break compacted

layers with safety, agility and reduced maintenance.

Manufactured with 5 and 7 shanks, this plow has a modern

structure with high resistance. The working depth is determined

by the cylinder stops installed on the hydraulic cylinder rods.

This plow model can be optionally supplied with:

• Disc blade: perfect to cut straw;

• Cage roller: Break the clods and facilitates the job of other

equipments, leaving a pre-leveled soil.

This operator's manual contains the necessary information

for the best performance of this plow. The operator must carefully

read the entire manual before working with the equipment. Also,

read and understand the safety recommendations.

For any further clarification or in the event of technical

problems that may arise during the service, consult your dealer

and the Technical Support department of the factory. They can

ensure the fully functioning of your Civemasa plow.

Содержание STAC M 500














































Результаты поиска

Содержание STAC M 500

Отзывы:

Похожие инструкции для STAC M 500

Бренды по названию

Популярные бренды

Civemasa STAC M 500, Руководство оператора

Результаты поиска

Содержание STAC M 500

Отзывы:

Похожие инструкции для STAC M 500

Бренды по названию

Популярные бренды