background image

Civemasa Implementos Agrícolas 

STAC M 500

3

To the owner

General information

Important

Right and left hand side indication are made observing the equipment from the rear.
To order any parts or request technical assistance services, it is required to provide 

the data contained on the nameplate, which is located on the equipment frame.

The acquisition of any Civemasa product assures to the original purchaser the following 

rights:

• Warranty certificate;
• Operator's manual;
• Technical assistance by the dealer on equipment delivery.
However, the owner must check the condition of the equipment on delivery, as well as 

knowing the warranty terms.

Special attention should be given to the safety recommendations, operation precautions 

and maintenance of the equipment.

The instructions in this manual indicates how to get the best performance and allow 

the operator to get maximum income, increasing the equipment lifetime.

This manual should be read by operators and maintenance staff.

• Only people who own a full knowledge of the tractor and equipment must 

transport, operate and carry out any maintenance on them;

• Civemasa is not responsible for any damage caused by accident on 

transporting, incorrect utilization or inadequate storage, either by 

negligence and/or lack of experience from any person;

• Civemasa is not responsible for any damage caused by unpredictable 

situations or the incorrect use of the equipment.

The warranty shall not be applied to any equipment, or any parts thereof, 

which has been altered elsewhere than at the place of manufacture or which 

the original purchaser thereof, at retail, has used or allowed to be used parts, 

not made or supplied by Civemasa.

NOTE

Содержание STAC M 500














































Отзывы: