Cisco TOPSPIN SFS 3012 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 79

background image

viii

CAUTION:

Grounding is supplied by the ground-prong on the 3-prong power cable. Do not attach a

separate ground cable. Do not use adapter plugs. Do not remove the ground prong from the cable.
Ensure the ground connection on the power supply is correct and functioning before applying power to
the Topspin 360.

CAUTION:

Always ground yourself before touching any internal Topspin 360 component to avoid

damage from electrostatic discharge (ESD).

CAUTION:

The Topspin 360 has two power cables. The operator must disconnect all power cables

before attempting to remove the Topspin 360 from the rack.

CAUTION:

Remove power cables by grasping the cable connector and pulling straight out.If the

chassis comes equipped with a power-plug retainer, move the bail wire used to retain the plug to the side
before attempting to remove the power plug. To replace power-supply cables, grasp the cable connector,
align the connector with the power jack, and insert the connector straight into the jack. If the chassis
comes equipped with a power-plug retainer, move the bail wire back into place to keep the power plug
firmly in place.

CAUTION:

The Topspin 360 contains lithium batteries. Do not attempt to replace or discard these

batteries. The batteries may only be serviced by Topspin service personnel.

CAUTION:

Observe and follow service markings. Do not service the Topspin 360, except as explained

in the Topspin documentation supplied with your Topspin 360. Opening the chassis or removing the
enclosure cover exposes you to electrical shock and may damage Topspin 360 components.

If one or more of the following situations occurs, remove power to the Topspin 360 and contact your
Topspin support representative:
•

The power cable or power plug is damaged.

•

The Topspin 360 has been exposed to water.

•

The Topspin 360 has been dropped or damaged in any way.

•

The Topspin 360 does not operate correctly after following the installation instructions.

CAUTION:

You must ensure the operating environment has adequate air circulation. Keep the Topspin

360 in a cool, well-ventilated room. Do not block cooling vents. Install filler panels into all unused
slots.

«
...
6
7
8
9
10
...
»

Содержание TOPSPIN SFS 3012
















































































Отзывы:

Нет отзывов

Похожие инструкции для TOPSPIN SFS 3012

Бренд: G&D Страницы: 36

Бренд: Delta Страницы: 4

Бренд: Eaton Страницы: 2

INTEGRA KLI 310

Бренд: Velux Страницы: 9

Custom Pro Matrix

Бренд: Bluestream Страницы: 27

Бренд: Omron Страницы: 4

Бренд: Radial Engineering Страницы: 8

Бренд: Farallon Страницы: 22

Бренд: StarTech.com Страницы: 2

Бренд: Hama Страницы: 32

Бренд: Santon Страницы: 16

Бренд: N-Tron Страницы: 2

Бренд: Omron Страницы: 31

Бренд: Novus Страницы: 16

EG5-0702-SFP Series

Бренд: Leonton Страницы: 21

Бренд: CP Electronics Страницы: 8

Бренд: Datavideo Страницы: 90

Бренд: SALZ Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды