Cisco PA-2FE-FX T Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 78

background image

1-4

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 1 Overview

LEDs

Note

PA-2FE-FX uses 62.5/125-micron multimode fiber with an SC connector.

LEDs

The PA-2FE has seven LEDS; an ENABLED LED, and LINK, TRANSMIT, and RECEIVE LEDs for
each port. The LEDs are shown in

Figure 1-4

.

Figure 1-4

LEDs on the PA-2FE—Faceplate View of PA-2FE-TX

After system initialization, the ENABLED LED goes on to indicate that the PA-2FE is ready for
operation. The following conditions must be met before the ENABLED LED goes on:

•

The PA-2FE is correctly connected and receiving power.

•

A PA-2FE–equipped card or chassis contains a valid microcode version that has been successfully
downloaded.

•

The bus recognizes the PA-2FE.

If any of these conditions are not met, or if the initialization fails for other reasons, the ENABLED LED
does not go on.

Table 1-2

lists LED colors and indicator functions.

Receptacles, Cables, and Pinouts

The two interface receptacles on the PA-2FE are a single RJ-45 connection (on the PA-2FE-TX) or an
SC-type optical-fiber connection (on the PA-2FE-FX). Each connection supports IEEE 802.3u interfaces
compliant with the 100BASE-X and 10/100BASE-T standards. The RJ-45 connection does not require
an external transceiver.

46453

ENABLED

LINK0

TX0

RX0

RX1

LINK1

TX1

PA-2FE-TX

0

1

Table 1-2

PA-2FE LEDs

LED Label

Color

State

Function

ENABLED

Green

On

Port adapter is enabled for operation.

LINK0

Green

On

Port 0 is receiving a carrier signal from the network.

1

1.

When an RJ-45 or SC port is active.

TX0

Green

On

Port 0 is transmitting data.

RX0

Green

On

Port 0 is receiving data.

RX1

Green

On

Port 1 is receiving data.

TX1

Green

On

Port 1 is transmitting data.

LINK1

Green

On

Port 1 is receiving a carrier signal from the network.

1

«
...
18
19
20
21
22
...
»

Содержание PA-2FE-FX T















































































Отзывы:

Нет отзывов

Похожие инструкции для PA-2FE-FX T

Бренд: Telex Страницы: 6

Бренд: Hama Страницы: 14

Бренд: Belkin Страницы: 18

Бренд: IFM Страницы: 10

Бренд: Cognex Страницы: 18

Бренд: 3idee Страницы: 7

Бренд: Moes Страницы: 14

Бренд: Intellinet Страницы: 3

Бренд: Ralink Страницы: 36

Бренд: Solwise Страницы: 25

Бренд: l-com Страницы: 54

Бренд: Tripp Lite Страницы: 4

Mini Port Replicator

Бренд: Keyspan Страницы: 41

Бренд: LM Technologies Страницы: 27

Бренд: Keyspan Страницы: 40

Бренд: Targus Страницы: 8

Бренд: Dynex Страницы: 1

Бренд: D-Link Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды