Cisco PA-2FE-FX T Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 78

background image

4-6

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 4 Configuring the PA-2FE

Configuring the Interfaces

Step 6

Reenable interfaces by doing the following:

a.

Repeat Step 3 to reenable an interface. Substitute the

no shutdown

command for the

shutdown

command.

b.

Repeat Step 4 to write the new configuration to NVRAM. Use the

copy running-config startup-config

command.

c.

Repeat Step 5 to verify that the interfaces are in the correct state. Use the

show interfaces

command followed by the interface type and interface address of the interface.

For complete descriptions of software configuration commands, refer to the publications listed in the

“Related Documentation” section on page viii

.

Performing a Basic Configuration

Following are instructions for a basic configuration: enabling an interface, and specifying IP routing.
You might also need to enter other configuration commands, depending on the requirements for your
system configuration and the protocols you plan to route on the interface. For complete descriptions of
configuration commands and the configuration options available for Fast Ethernet interfaces, refer to the
appropriate software documentation.

Cisco 7304 PCI port adapter carrier
card in Cisco 7304 routers

show interfaces fastethernet,

followed by

slot-number/port-number

(module-slot-number/
interface-port-number)

The example is for interface 0 of a PA-2FE in a
Cisco 7304 PCI port adapter carrier card in
module slot 3 of a Cisco 7304 router.

Router#

show interfaces fastethernet 3/0

FastEthernet3/0 is down, line protocol is

down

Cisco 7401ASR routers

show interfaces fastethernet

,

followed by

slot/port

(port-adapter-slot-number/
interface-port-number)

The example is for interface 0 on a PA-2FE in port
adapter slot 1.

Router#

show interfaces fastethernet 1/0

fastethernet 1/0 is administratively down,

line protocol is down

[Additional display text omitted from this

example]

VIP in Cisco 7500 series routers

show interfaces fastethernet

,

followed by

slot/port adapter/port

(interface-processor-slot-number/
port-adapter-slot-number/
interface-port-number)

The example is for interface 0 on a PA-2FE in port
adapter slot 1 of a VIP in interface processor
slot 1.

Router#

show interfaces fastethernet 1/1/0

fastethernet 1/1/0 is administratively

down, line protocol is down

[Additional display text omitted from this

example]

Table 4-2

Examples of the show interfaces Command (continued)

Platform

Command

Example

«
...
62
63
64
65
66
...
»

Содержание PA-2FE-FX T















































































Отзывы:

Нет отзывов

Похожие инструкции для PA-2FE-FX T

Бренд: HAGOR Страницы: 8

GM-FTDI2-LED16-C

Бренд: GearMo Страницы: 6

Бренд: Radio Shack Страницы: 1

Бренд: J5create Страницы: 2

Бренд: NetComm Страницы: 2

Бренд: Zonet Страницы: 62

Бренд: ConvaTec Страницы: 4

Бренд: Renesas Страницы: 26

Бренд: Hainbuch Страницы: 64

Бренд: WeGoodSun Страницы: 8

Бренд: Freelinc Страницы: 2

BasicXL BXL-NBT-AC01

Бренд: nedis Страницы: 16

Бренд: nedis Страницы: 30

Бренд: nedis Страницы: 2

Бренд: Mi Home Страницы: 13

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды