Cisco PA-2FE-FX T Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 78

background image

4-16

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 4 Configuring the PA-2FE

Checking the Configuration

Using the show interfaces Command

The

show interfaces

command displays status information (including the physical slot and interface

address) for the interfaces you specify. All of the examples that follow specify Fast Ethernet interfaces.

For complete descriptions of interface commands and the configuration options available for
Cisco 7100 series, Cisco 7200 series, Cisco uBR7200 series, the Cisco 7301 router, the Cisco 7401ASR,
and the VIP interfaces in the Cisco 7500 routers, refer to the publications listed in the

“Related

Documentation” section on page viii

. The following examples show output for the

show interfaces

command on some of the platforms that support the PA-2FE.

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

Cisco 7100 Series Routers

Following is an example of the

show interfaces

command used with a Cisco 7140 series router.

In this example, the two Fast Ethernet interfaces (0 and 1) are on a port adapter in port adapter slot 4 of a
Cisco 7140 series router; also, most of the status information for each interface is omitted. (Interfaces
are administratively shut down until you enable them.)

Router#

show interfaces fastethernet 4/1

FastEthernet4/1 is up, line protocol is up

Hardware is i82543 (Livengood), address is 00b0.4a3c.e071 (bia 00b0.4a3c.e071)

Internet address is 10.0.0.1/8

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s

ARP type:ARPA, ARP Timeout 04:00:00

Last input 00:00:43, output 00:00:06, output hang never

Last clearing of "show interface" counters 00:03:54

Queueing strategy:fifo

Output queue 0/40, 5 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

26 packets input, 4922 bytes

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

50 packets output, 7016 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

1 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Note

To use the

show interfaces fastethernet

command with the Cisco 7120 series router, replace the

interface address arguments 4/0 and 4/1, with 3/0 and 3/1, respectively.

«
...
72
73
74
75
76
...
»

Содержание PA-2FE-FX T















































































Отзывы:

Нет отзывов

Похожие инструкции для PA-2FE-FX T

Бренд: H3C Страницы: 37

Бренд: Teufel Страницы: 24

Бренд: ZyXEL Communications Страницы: 7

Бренд: Goobay Страницы: 4

Бренд: Apricorn Страницы: 4

Thunderbolt MTB3-002-HD

Бренд: Tripp Lite Страницы: 31

Бренд: ST-Lab Страницы: 4

Бренд: TP-Link Страницы: 37

Xcomfort CSAP-01/0 Series

Бренд: Moeller Страницы: 4

Linksys SPA9000

Бренд: Linksys Страницы: 246

Бренд: NETGEAR Страницы: 2

Бренд: Bravekit Страницы: 17

FoneMate SFA-0001

Бренд: TeleVue Страницы: 2

Бренд: Telex Страницы: 136

Бренд: Sveon Страницы: 45

USB-GPIB-L Adapter

Бренд: Rigol Страницы: 20

Бренд: Corinex Страницы: 26

Бренд: SOHARD Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды