Cisco PA-2FE-FX T Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 78

background image

4-13

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 4 Configuring the PA-2FE

Checking the Configuration

1 VIP2 controller (2 FastEthernet).

1 VIP2 R5K controller (2 FastEthernet).

6 Ethernet/IEEE 802.3 interface(s)

4 FastEthernet/IEEE 802.3 interface(s)

123K bytes of non-volatile configuration memory.

8192K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

20480K bytes of Flash PCMCIA card at slot 1 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

No slave installed in slot 7.

Configuration register is 0x100

Using the show diag Command

Display the types of port adapters installed in your system (and specific information about each) using
the

show diag

slot

command, where

slot

is the port adapter slot in a Cisco 7100 series routers,

Cisco 7200 series router, Cisco uBR7200 series routers, Cisco 7300 series routers, or the
Cisco 7401ASR router and the interface processor slot in a Cisco 7500 series router with a VIP. The
examples show output for the

show diag

command on some of the platforms that support the PA-2FE.

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

Cisco 7100 Series Routers

Following is an example of the

show diag

slot

command that shows a

Fast Ethernet port adapter

in

port adapter slot 4 of a Cisco 7140 series router:

Router#

show diag 4

Slot 4:

Dual Port FastEthernet (MMF) Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time 00:04:17 ago

EEPROM contents at hardware discovery:

Hardware Revision :1.0

PCB Serial Number :MIC05022Q6M

Part Number :73-5420-04

Board Revision :A0

RMA Test History :00

RMA Number :0-0-0-0

RMA History :00

Deviation Number :0-0

Product Number :PA-2FE-FX

Top Assy. Part Number :800-08352-04

EEPROM format version 4

EEPROM contents (hex):

0x00:04 FF 40 02 25 41 01 00 C1 8B 4D 49 43 30 35 30

0x10:32 32 51 36 4D 82 49 15 2C 04 42 41 30 03 00 81

0x20:00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D

0x30:32 46 45 2D 46 58 20 20 20 20 20 20 20 20 20 20

0x40:20 C0 46 03 20 00 20 A0 04 FF FF FF FF FF FF FF

0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

«
...
69
70
71
72
73
...
»

Содержание PA-2FE-FX T















































































Отзывы:

Нет отзывов

Похожие инструкции для PA-2FE-FX T

PoE Injector Adapter POE-32001T

Бренд: UNICOM Страницы: 1

Бренд: Ralink Страницы: 27

Бренд: Tekram Technology Страницы: 4

Бренд: cable matters Страницы: 2

Бренд: Digitus Страницы: 34

Бренд: GAI-Tronics Страницы: 4

Бренд: Hamlet Страницы: 4

ALMEMO 8006-RTA3

Бренд: Ahlborn Страницы: 16

Бренд: KSH International Страницы: 18

Бренд: SMC Networks Страницы: 18

Wireless LAN Game Adapter W11

Бренд: Hama Страницы: 4

Бренд: König Страницы: 12

Бренд: Yealink Страницы: 32

Бренд: OBDLink Страницы: 12

Бренд: Eaton Страницы: 64

Бренд: ErGear Страницы: 20

Бренд: Sugar Страницы: 6

AV Device DIN Adapter

Бренд: EGi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды