Cisco PA-2FE-FX T Скачать руководство пользователя страница 29

Страница: 29 / 78

1-13

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

OL-3474-06

Chapter 1 Overview

Identifying Interface Addresses

Note

In Cisco 7200 series routers and Cisco uBR7200 series routers, port adapter slot 0 is reserved for the
Fast Ethernet port on the I/O controller, if present.

Cisco 7120 Router and Cisco 7140 Router Interface Addresses

This section describes how to identify the interface addresses used for the PA-2FE

in Cisco 7120 router

and the Cisco 7140 router.

The interface address is composed of a two-part number in the format

port-adapter-slot-number/interface-port-number.

See

Table 1-4

for the interface address format.

Cisco 7200 Series Routers Interface Addresses

This section describes how to identify the interface addresses used for the PA-2FE in Cisco 7200 series
routers.

The interface address is composed of a two-part number in the format

port-adapter-slot-number/interface-port-number.

See

Table 1-4

for the interface address format.

Cisco 7200 series routers
(Cisco 7202, Cisco 7204,
Cisco 7206, Cisco 7204VXR,
Cisco 7206VXR)

Port-adapter-slot-number/interface-port-number

Port adapter slot—1 through
6 (depends on the number of
slots in the router)

Interface port—0 or 1

1/0

Cisco uBR7200 Series
Universal Broadband Routers
(Cisco uBR7223,
Cisco uBR7246,
Cisco uBR7246VXR)

Port-adapter-slot-number/interface-port-number

Port adapter slot—1 and 2

Interface port—0 or 1

1/0

Cisco 7301 routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 1

Interface port—0 or 1

1/0

Cisco 7304 PCI port adapter
carrier card in Cisco 7304
routers

Module-slot-number/interface-port-number

Module slot—router module
slot 2 through 5

Interface port—0 or 1

3/0

Cisco 7401ASR routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 1

Interface port—0 or 1

1/0

VIP in Cisco 7500 series
routers

Interface-processor-slot-number/port-adapter-slot-
number/interface-port-number

Interface processor slot—0
through 12 (depends on the
number of slots in the
router)

Port adapter slot—always 0
or 1

Interface port—0 or 1

3/1/0

Table 1-4

Identifying Interface Addresses (continued)

Platform

Interface Address Format

Numbers

Syntax

Содержание PA-2FE-FX T















































































Результаты поиска

Содержание PA-2FE-FX T

Отзывы:

Похожие инструкции для PA-2FE-FX T

Бренды по названию

Популярные бренды

Cisco PA-2FE-FX T, Руководство по установке и настройке

Результаты поиска

Содержание PA-2FE-FX T

Отзывы:

Похожие инструкции для PA-2FE-FX T

Бренды по названию

Популярные бренды