manualshive.com logo in svg

Cisco PA-100VG, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-100VG Скачать руководство пользователя страница 4

4

PA-100VG AnyLAN Port Adapter Installation and Configuration

Port Adapter Installation Prerequisites

Caution

To prevent system problems, the VIP2 requires that the Cisco 7000 series router has the 7000 Series 

Route Switch Processor (RSP7000) and the 7000 Series Chassis Interface (RSP7000CI) installed. The VIP2 
will 

not

 operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor 

(SSP) installed in the Cisco 7000 series router.

Note

The minimum recommended VIP2 model is a VIP2-15.

List of Parts and Tools 

You need the following tools and parts to install a 100VG port adapter. If you need additional 
equipment, contact a service representative for ordering information.

•

For VIP2 users:

—

PA-100VG(=)

—

VIP2-15(=), VIP2-20=, VIP2-40(=) 

—

A Cisco 7500 series router with at least one available interface processor slot (or a 
Cisco 7000 series router with an RSP7000 installed and at least one available interface 
processor slot)

•

For Cisco 7200 series users:

—

PA-100VG(=)

—

A Cisco 7200 series router with at least one available port adapter slot

•

RJ-45 cables appropriate for the port adapter interfaces on your 100VG port adapter (RJ-45 
cables are not supplied by Cisco systems, but are available from commercial cable vendors)

•

Number 1 Phillips and a 3/16-inch, flat-blade screwdriver

•

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all 
upgrade kits, field-replaceable units (FRUs), and spares

Safety Guidelines

Following are safety guidelines that you should follow when working with any equipment that 
connects to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, 
might harm you. A warning symbol precedes each warning statement.

Warning

Means 

danger

. You are in a situation that could cause bodily injury. Before you work on 

any equipment, be aware of the hazards involved with electrical circuitry and be familiar with 
standard practices for preventing accidents. To see translations of the warnings that appear in this 
publication, refer to the 

Regulatory Compliance and Safety Information

 document that accompanied 

this device.

Содержание PA-100VG







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды