Cisco PA-100VG Скачать руководство пользователя страница 32

Страница: 32 / 38

PA-100VG AnyLAN Port Adapter Installation and Configuration

Cisco 7200 Series and 100VG Port Adapters

Using show Commands to Display Interface and System Information

To display information about a specific interface, use the

show interfaces

command with the

interface type and port address in the format

show interfaces

type

[

slot/interface

]. The following

example of the

show interfaces

type

[

slot/interface

]

command shows all of the information specific

to the first 100VG port (interface port 0) in port adapter slot 5:

Router#

show int vg 5/0

VG-AnyLAN5/0 is up, line protocol is up

Hardware is MC68852

Frame type is 802.3, address is 0060.09b9.9b28 (bia 0060.09b9.9b28)

Internet address is 10.1.1.6/16

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255

Encapsulation ARPA, loopback not set, keepalive set (10 sec)

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:01, output hang never

Last clearing of “show interface” counters never

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

687 packets input, 48114 bytes, 0 no buffer

Received 69 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 input packets with dribble condition detected

855 packets output, 59743 bytes, 0 underruns

0 output errors, 0 collisions, 3 interface resets

0 output buffer failures, 0 output buffers swapped out

0 vg alignment error, 0 vg balance error

0 vg invalid ipm error, 0 vg symbol error

0 vg skew error, 0 vg frame delimit error

Содержание PA-100VG







































Результаты поиска

Содержание PA-100VG

Отзывы:

Похожие инструкции для PA-100VG

Бренды по названию

Популярные бренды

Cisco PA-100VG, Руководство по установке и настройке

Результаты поиска

Содержание PA-100VG

Отзывы:

Похожие инструкции для PA-100VG

Бренды по названию

Популярные бренды