Cisco PA-100VG Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 38

Cisco PA-100VG Скачать руководство пользователя страница 19

PA-100VG AnyLAN Port Adapter Installation and Configuration

19

Configuring the 100VG AnyLAN Interfaces

Step 3

If IP routing is enabled on the system, you can assign an IP address and subnet mask to
the interface with the

ip address

configuration subcommand, as in the following

example:

Router(config-if)#

ip address 1.1.1.10 255.255.255.0

Step 4

Add any additional configuration subcommands required to enable routing protocols and
set the interface characteristics.

Step 5

Change the shutdown state to up and enable the interface as follows:

Router(config-if)#

no shutdown

Step 6

Configure additional interfaces as required.

Step 7

When you have included all of the configuration subcommands to complete the
configuration, press

Ctrl-Z

to exit configuration mode.

Step 8

Write the new configuration to nonvolatile memory as follows:

Router#

copy running-config startup-config

[OK]

Router#

To check the interface configuration using

show

commands, proceed to the section “Checking the

Configuration.”

Checking the Configuration

This section provides information for checking your configuration. After configuring the new
interface, use the

show

commands to display the status of the new interface or all interfaces, and use

the

ping

command to check connectivity.

Using show Commands to Verify the New Interface Status

The following steps use

show

commands to verify that the new interfaces are configured and

operating correctly.

Step 1

Display the system hardware configuration with the

show version

command to ensure

that the list includes the new interfaces.

Step 2

Display all the current interface processors and their interfaces with the

show

controllers

cbus

command. Verify that the new 100VG port adapter appears in the correct slot.

Step 3

Specify one of the new interfaces with the

show interfaces

type

slot/port

adapter/interface

command and verify that the first line of the display specifies the

interface with the correct slot number. Also verify that the interface and line protocol are
in the correct state: up or down.

Step 4

Display the protocols configured for the entire system and specific interfaces with the

show protocols

command. If necessary, return to configuration mode to add or remove

protocol routing on the system or specific interfaces.

Step 5

Display the running configuration file with the

show running-config

command. Display

the configuration stored in NVRAM using the

show startup-config

command. Verify

that the configuration is accurate for the system and each interface.

If the interface is down and you configured it as up, or if the displays indicate that the hardware is
not functioning properly, ensure that the network interface is properly connected and terminated. If
you still have problems bringing the interface up, contact a service representative for assistance.

«
...
17
18
19
20
21
...
»

Содержание PA-100VG







































Отзывы:

Нет отзывов