Cisco Catalyst 9200 Series Скачать руководство пользователя страница 75

Страница: 75 / 78

RJ-45 Console Port LED

Table 25: RJ-45 Console Port LED

RJ-45 Console Port Status

Color

RJ-45 console is disabled. USB console is active.

Off

RJ-45 console is enabled. USB console is disabled.

Green

Fan LED

Table 26: Fan LED Indicator

Description

Color/State

The fan is not receiving power; the fans have stopped.

Off

All fans are operating normally.

Green

One or more fans have encountered tachometer faults.

Amber

One or more fans' tachometer faults have exceeded the maximum limit.

Red

Uplink Port LEDs

The uplink ports have various status LEDs. Each port LED is labeled according to its module status.

• For SFP ports, a G labeling nomenclature is used, where G = 1 Gigabit. The The G label appears to the

left of the uplink port LED.

• For SFP+ ports, a 10G labeling nomenclature is used, where 10G = 10 Gigabit. The 10G label appears

to the left of the uplink port LED. SFP+ module ports support both SFP+ and SFP modules

• For SFP28 ports, a 25G labeling nomenclature is used, where 25G = 25 Gigabit. The The G label appears

to the left of the uplink port LED.

• For QSFP+ ports, a 40G labeling nomenclature is used, where 40G = 40 Gigabit. The The G label appears

to the left of the uplink port LED.

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

Switch LEDs

RJ-45 Console Port LED

Содержание Catalyst 9200 Series














































































Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 9200 Series, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды