Cisco Catalyst 9200 Series Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 78

background image

Figure 31: AC-Power Supply with Power Cord Retainer

Retainer clamp

4

Power cord

1

The strap end that is fixed
to the power supply
module

5

Tabs on the retainer clamp

2

-

-

Power cord retainer strip

3

a) Fix the strap in the power cord retainer to the power supply module, to hold the clamp in place.
b) Slide the retainer clamp around the AC power cord and position the retainer closest to the power supply.

Depending on the width of the power cord, adjust the size of the retainer clamp, if required.

Note

c) Press the tabs on the retainer clamp towards each other to secure the AC power cord.

Step 7

Connect the power cord to the power supply and to an AC power outlet. Turn on the power at the power
source.

Step 8

Confirm that the power supply AC OK and PS OK LED are green.

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

47

Installing a Power Supply Unit

Installing or Replacing an AC Power Supply Module

«
...
51
52
53
54
55
...
»

Содержание Catalyst 9200 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 9200 Series

WJSX150 - SWITCHER - ADDENDUM

Бренд: Panasonic Страницы: 48

Бренд: FANATEC Страницы: 40

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 62

DXS-3410 Series

Бренд: D-Link Страницы: 54

Бренд: CZHOON Страницы: 4

NAMUR BES G06MD-GNX10B-EV02-EEX

Бренд: Balluff Страницы: 56

Бренд: Omron Страницы: 16

Бренд: Hama Страницы: 56

Бренд: NA-DE Страницы: 4

Бренд: I-Rocks Страницы: 18

SUPERHUB QUATTRO

Бренд: Manhattan Страницы: 2

Бренд: Led Control Страницы: 22

EX78900X Series

Бренд: EtherWAN Страницы: 2

Бренд: G&D Страницы: 76

Бренд: Linksys Страницы: 3

Бренд: Brookstone Страницы: 24

Бренд: mind alive Страницы: 16

Бренд: H3C Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды