Cisco Catalyst 9200 Series Скачать руководство пользователя страница 70

Страница: 70 / 78

Table 19: Console LED

Description

Color

LED

USB Mini-Type B console port is
active.

Solid green

Console

USB cable not connected

Off

System LED

Table 20: System LED

System Status

Color

System is not powered on.

Off

System is operating normally.

Green

System is loading the software.

Blinking green

System is receiving power but is not functioning
properly.

Amber

There is a fault with one of the following:

• Network module (non traffic-related)

• Power supply

• Fan module

Blinking amber

ACTIVE LED

Table 21: ACTIVE LED

Description

Color

Switch is not the active switch.

Off

Switch is the stack's active switch or a standalone switch.

Green

Switch is in stack standby mode.

Fast blinking green

An error occurred when the switch was selecting the stack's active switch, or another
type of stack error occurred.

Amber

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

Switch LEDs

System LED

Содержание Catalyst 9200 Series














































































Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 9200 Series, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды