Cisco Catalyst 9200 Series Скачать руководство пользователя страница 34

Страница: 34 / 78

Figure 19: Attaching the mounting feet for Table-Mounting or Shelf-Mounting

Rubber mounting feet

Step 3

Place the switch on the table or shelf near an AC power source.

What to do next

When you complete the switch installation, see

After Switch Installation, on page 28

for information on

switch configuration.

After Switch Installation

• Configure the switch using the Web User Interface. For more information, see "Configuring the Switch

Using the Web User Interface" topic in the

Software Configuration Guide

• Connect the required devices to the switch ports.

• Turn on the power supply switches to power up the system. While powering up, the switch performs a

series of bootup diagnostic tests.

The switch is designed to boot up in less than 30 minutes, provided that the
neighboring devices are in fully operational state.

Note

• Verify port connectivity after connecting devices to the switch ports. The LED turns green when the

switch and the attached device have a link.

Cisco Catalyst 9200 Series Switches Hardware Installation Guide

Installing the Switch

After Switch Installation

Содержание Catalyst 9200 Series














































































Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды

Cisco Catalyst 9200 Series, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 9200 Series

Отзывы:

Похожие инструкции для Catalyst 9200 Series

Бренды по названию

Популярные бренды