SUMMARY STEPS
1.
Remove the standby RP by performing the procedure described in the xref
“
Removing the Cisco ASR
1000 Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers
”
section.
2.
Remove the DIMM memory module from the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
3.
Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
4.
Insert the standby RP by performing the procedure described in the xref
“
Removing the Cisco ASR 1000
Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers
”
section.
5.
Verify the memory upgrade on the standby RP by running the following commands:
6.
Use the
redundancy force-switchover
command to switch the upgraded standby RP to the active state.
The RP that was in the active state moves to the standby state.
7.
Repeat Step 1 through Step 5 on the standby RP.
DETAILED STEPS
Step 1
Remove the standby RP by performing the procedure described in the xref
“
Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers
”
section.
Step 2
Remove the DIMM memory module from the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 3
Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
•
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 4
Insert the standby RP by performing the procedure described in the xref
“
Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers
”
section.
Step 5
Verify the memory upgrade on the standby RP by running the following commands:
Example:
Router#
configure terminal
Router(config-red)#
redundancy
Router(config-r-mc)#
main-cpu
Router(config-r-mc)#
standby console enable
Router(config-r-mc)#
end
Router-stby#
show version
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version
Cisco ASR 1000 Series Router Hardware Installation Guide
496
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing and Replacing the DIMM Memory Modules on the Cisco ASR 1006 Router and the Cisco ASR 1013 Router
Содержание ASR 1001
