Cisco APP-LTR2 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 36

Cisco APP-LTR2 Скачать руководство пользователя страница 36

36 ciscoBus Token Ring Card and Applique Installation and Upgrade Instructions

Cisco Information Online

If you are a network administrator and need personal technical assistance with a Cisco product that
is under warranty or covered by a maintenance contract, contact Cisco’s Technical Assistance Center
(TAC) at 800 553-2447, 408 526-7209, or

[email protected]

. To obtain general information about

Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or

[email protected]

.

This document is to be used in conjunction with the AGS+ Hardware Installation and Maintenance publication.

Access Without Compromise, Catalyst, CD-PAC, CiscoFusion, CiscoView, CiscoWorks, HyperSwitch, Internetwork Operating System, IOS, Netscape, Point and Click Internetworking,
SMARTnet, SynchroniCD, The Packet, UniverCD, Workgroup Director, and Workgroup Stack are trademarks; Access by Cisco and Bringing the power of internetworking to everyone
are service marks; and Cisco, Cisco Systems, and the Cisco logo are registered trademarks of Cisco Systems, Inc. All other trademarks, service marks, registered trademarks, or registered
service marks mentioned in this document are the property of their respective owners.

Copyright © 1994, Cisco Systems, Inc.
All rights reserved. Printed in USA.

949R

«
...
34
35
36

Содержание APP-LTR2





































Отзывы:

Нет отзывов