Cisco APP-LTR2 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

Cisco APP-LTR2 Скачать руководство пользователя страница 13

ciscoBus Token Ring Card and Applique Installation and Upgrade Instructions 13

Installation Prerequisites

Caution

The maximum number of Token Ring interfaces in a chassis is 16, which is the result of

installing 4 CSC-2Rs and 2 CSC-C2CTRs. (Two ciscoBus slots are used as Multibus slots.) The
number of ciscoBus interfaces is limited by space available for applique card cages and power
budget limits. Because the slower Multibus interfaces always have higher priority than ciscoBus
interfaces, traffic on the Multibus may degrade performance of ciscoBus interfaces that are not
autonomously switched; therefore, we do not recommend this configuration for
performance-sensitive applications.

Figure 7

AGS+ Top View

Power Budget

In an AGS+ shipped on or after October 1, 1991, the total power drawn by all installed cards must
not exceed 300W per chassis. In AGS+ chassis shipped before October 1, 1991, the total power must
not exceed 260W. (The earlier chassis contained a 5A circuit breaker, rather than the 7.5A circuit
used in the current chassis configuration.) Table 4 lists the power requirements for each card
available for the AGS+, including the CSC-C2CTR. The values for the CSC-C2CTR were measured
with four Token Ring interfaces active and include power drawn by the appliques.

Note

In addition to the power budget, other restrictions apply when other ciscoBus interface cards

or Multibus Token Ring interface cards are installed in the system. For compatibility limitations,
refer to the following section, “Compatibility with Other Cards.”

H1260a

Front of chassis

System
card cage

Applique
card cages

MAS-10
blower

«
...
11
12
13
14
15
...
»

Содержание APP-LTR2





































Отзывы:

Нет отзывов