Cisco 7821 Скачать руководство пользователя страница 305

Страница: 305 / 360

Description

Parameter

Enables or disables DND status sync on a line via XSI
service.

Choose

Yes

to enable the phone to synchronize DND

status with the server using the XSI service. Choose

to disable this feature.

Note

• When

Feature Key Sync

is set to

Yes

, FKS takes precedent over XSI

synchronization.

• If XSI host server and credentials are

not entered and the

DND Enable

field

is set to

Yes

, the phone user can't turn

on DND mode on the phone.

DND Enable

Audio Configuration

Description

Parameter

Preferred codec for all calls. The actual codec used
in a call still depends on the outcome of the codec
negotiation protocol.

Select one of the following:

• G711u

• G711a

• G729a

• G729ab

• G722

• G722.2

• iLBC

• OPUS

• iSAC

Default: G711u

Preferred Codec

Select

to use any code. Select

Yes

to use only the

preferred codes. When you select Yes, calls fail if the
far end does not support the preferred codecs.

Default: No

Use Pref Codec Only

Codec to use if the first codec fails.

Default: Unspecified

Second Preferred Codec

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

291

Cisco IP Phone Troubleshooting

Audio Configuration

Содержание 7821









































































































































































































































































































































































Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды

Cisco 7821, Руководство администратора

Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды