Cisco 7821 Скачать руководство пользователя страница 221

Страница: 221 / 360

•

Tx (Packets)

—Transmitted packets from the phone.

•

Rx (Packets)

—Received packets from the phone.

View the Status Messages on the Phone

Procedure

Step 1

Press

Applications

Step 2

Select

Status

Status messages

You can view a log of the various phone statuses since provisioning was last done.

Status messages reflect UTC time and are not affected by the timezone settings on the phone.

Note

Step 3

Press

Back

View the Network Status

Procedure

Step 1

Press

Applications

Step 2

Select

Status

Network Status

You can view the following information:

•

Network type

—Indicates the type of Local Area Netwrok (LAN) connection that the phone uses.

•

Network status

—Indicates if the phone is connected to a network.

•

IPv4 status

—IP address of the phone. You can see information on IP address, Addressing type, IP status,

Subnet mask, Default router, Domain Name Server (DNS) 1, DNS 2 of the phone.

•

IPv6 status

—IP address of the phone. You can see information on IP address, Addressing type, IP

status, Subnet mask, Default router, Domain Name Server (DNS) 1, DNS 2 of the phone.

•

VLAN ID

—VLAN ID of the phone.

•

MAC address

—Unique Media Access Control (MAC) address of the phone.

•

Host name

—Displays the current host name assigned to the phone.

•

Domain

—Displays the network domain name of the phone. Default: cisco.com

•

Switch port link

—Status of the switch port.

•

Switch port config

—Indicates speed and duplex of the network port.

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

207

Cisco IP Phone Troubleshooting

View the Status Messages on the Phone

Содержание 7821









































































































































































































































































































































































Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды

Cisco 7821, Руководство администратора

Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды