Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 50

background image

3-2

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 3 Removing and Installing Line Cards

Handling Line Cards

Handling Line Cards

Caution

Always handle the line card by the carrier edges and handle; never touch the line card components or
connector pins. (See

.)

Figure 3-1

Handling a Line Card

Online Insertion and Removal

The Cisco 7304 router supports online insertion and removal (OIR) of line cards; therefore, you do not
have to power down the router when removing and replacing an OC12 POS line card on a Cisco 7304
router. The Cisco 7304 router also supports CLI-controlled OIR (see the

“CLI-Controlled OIR” section

), which allows for the completion of data traffic before the active interfaces are shut down.

Note

As you disengage the line card from the router, online insertion and removal (OIR) administratively
shuts down all active interfaces in the line card.

Note

Before you begin installation, read

Chapter 2, “Preparing for Installation,”

for a list of parts and tools

required for installation.

Warnings and Cautions

Observe the following warnings and cautions when installing or removing line cards.

Note

If a line card lever or other retaining mechanism does not move to the locked position, the line card is
not completely seated in the backplane. Carefully pull the line card halfway out of the slot, reinsert it,
and move the line card lever to the locked position.

57702

Metal carrier

Printed circuit board

«
...
30
31
32
33
34
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: IBM Страницы: 144

Бренд: MADRIX Страницы: 36

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

Бренд: tau Страницы: 9

Бренд: tau Страницы: 8

Бренд: POLA Страницы: 2

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: Zaiput Flow Technologies Страницы: 10

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренд: MT-Propeller Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды