Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 50

background image

C H A P T E R

2-1

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

2

Preparing for Installation

This chapter provides the general equipment, safety, and site preparation requirements for installing the
OC12 POS line card. This chapter contains the following sections:

•

Required Tools and Equipment, page 2-1

•

Software and Hardware Requirements, page 2-2

•

Checking Hardware and Software Compatibility, page 2-2

•

Safety Guidelines, page 2-2

•

FCC Class A Compliance, page 2-6

Required Tools and Equipment

You need the following tools and parts to install a line card. If you need additional equipment, contact
a service representative for ordering information.

•

OC12 POS line card (For information about the specific OC12 POS line card models, see the

Card Overview” section on page 1-1

•

SC-type single-mode optical fiber cables to connect the interfaces with the network (Single-mode
optical fiber cables for the OC12 POS line cards are not available from Cisco Systems but are
available from commercial cable vendors. For information about optical fiber cables, see the

POS Line Card Optical Fiber Specifications” section on page 1-5

and the

“Cables and Connectors”

section on page 1-8

•

Number 1 Phillips screwdriver

•

Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist
strap included with all upgrade kits, field-replaceable units (FRUs), and spares

•

Antistatic mat and antistatic container

«
...
23
24
25
26
27
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: Quickmill Страницы: 3

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: ZKTeco Страницы: 6

Бренд: Ultraflex Страницы: 7

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: Cypress Страницы: 3

IB-TRON 4000 SOL

Бренд: INSBUD Страницы: 14

Бренд: bluelab Страницы: 39

Бренд: SOMFY Страницы: 2

COMBIVERT F4-S/1.2

Бренд: KEB Страницы: 96

Бренд: Exhausto CDT Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды