Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 50

background image

2-6

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 2 Preparing for Installation

FCC Class A Compliance

FCC Class A Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case users will be
required to correct the interference at their own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference
stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment
causes interference to radio or television reception, try to correct the interference by using one or more
of the following measures:

•

Turn the television or radio antenna until the interference stops.

•

Move the equipment to one side or the other of the television or radio.

•

Move the equipment farther away from the television or radio.

•

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is,
make certain the equipment and the television or radio are on circuits controlled by different circuit
breakers or fuses.)

Note

The OC12 POS line card has been designed to meet these requirements. Modifications to this product
that are not authorized by Cisco Systems, Inc. could void the various approvals and negate your authority
to operate the product.

«
...
28
29
30
31
32
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: GE Страницы: 425

Бренд: Ohsung Electronics Страницы: 18

Бренд: Magnescale Страницы: 132

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Parker Страницы: 44

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Panamax Страницы: 16

Бренд: Linear Technology Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды