Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 50

background image

2-2

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 2 Preparing for Installation

Software and Hardware Requirements

Software and Hardware Requirements

The table below lists the minimum Cisco IOS software release required to use the OC12 POS line card
in the Cisco 7304 router.

For all systems in which you install the OC12 POS line card, use the show version command to display
the current configuration of the router, including the system software version that is currently loaded and
running. Use the show diag slot command to view specific information about the hardware installed in
your system.

Checking Hardware and Software Compatibility

To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether
modules within a system are compatible, but it does provide the minimum IOS requirements for
individual hardware modules or components.

Note

Access to this tool is limited to users with Cisco.com login accounts.

To access Software Advisor, click Login at Cisco.com and go to Technical Support Help—Cisco
TAC: Tool Index: Software Advisor. You can also access the tool by pointing your browser directly to

http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl

Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.

Safety Guidelines

This section provides safety guidelines that you should follow when working with any equipment that
connects to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might
harm you. A warning symbol precedes each warning.

Table 2-1

OC-12 POS Line Card Software Requirements

Platform

Recommended Minimum Cisco IOS Release

Cisco 7304 Router

1

1.

The OC12 POS line card requires a Network Services Engine 100 (NSE-100) to operate.

Cisco IOS Release 12.1(10)EX or a later release of Cisco IOS Release 12.1 EX

«
...
24
25
26
27
28
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: ABB Страницы: 2

Бренд: Falcon Страницы: 3

Бренд: jbc Страницы: 4

Бренд: C&K systems Страницы: 2

Бренд: Samson Страницы: 48

Бренд: Eaton Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: Viva Страницы: 9

Бренд: HANYOUNG NUX Страницы: 4

FLECK 5810 XTR2

Бренд: Pentair Страницы: 36

Бренд: Wavelength Electronics Страницы: 17

Бренд: Rheem Страницы: 2

Бренд: Daikin Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды