manualshive.com logo in svg

Cirronet SEM2410, Руководство пользователя

Поделиться
Скачать
Cirronet SEM2410 Скачать руководство пользователя страница 18

 

 2000, 2001  Cirronet

 Incorporated 

15

 M-2410-0007 Rev - 

 

network The radio in the SEM has 64 preprogrammed hopping patterns or network 

numbers. By using different network numbers, nearby co-located networks 
can avoid interfering with each other’s transmissions. Even if both 
networks tried to use the same frequency, on the next hop they would be at 
different frequencies. 

nwt

 can range from 0 to 63. 

param This command allows certain special radio parameters to be modified. 

These are only useful in debugging circumstances and should not be used 
unless directed to by Cirronet Technical Support. Modifying these 
parameters without direction by Cirronet may render the equipment 
inoperable. 

show This command displays a list of the current radio parameters including the 

network number, maxremotes and the sys outmax value. 

Distance Optimization 

In installations where the distance between SEMs will be more than 1/10 of a mile, the 
distance optimization parameter should be set in the remote SEMs. This parameter is set 
using the 

radio a param

 command with 

dx

 as the sub-command. The dx sub-command 

has a single argument that is a hexadecimal value between 0 and FF. The default setting 
of 00H is suitable for ranges of 0 to 0.8 miles (1287 m), with optimal performance at 0.1 
miles (162m).  Each increment of this parameter adds 0.1 miles (162 m) to the working 
range. Thus the optimal and max ranges are determined by: 

 
 optimal = 0.1mi + 0.1mi x 

dx 

= 0.162km + 0.162km x 

dx

 

 max = 0.8mi + 0.1mi x 

dx = 

1.33km + 0.162km x

 dx

 

 

The following table presents various values of dx and the associated optimal and max 
ranges. 

 

dx setting 

range: 

min

 

  

optimal 

 

max 

00H 

0mi/0km 

0.1mi/0.2km 

0.8mi/1.3km 

01H 

0mi/0km 

0.2mi/0.3km 

0.9mi/1.5km 

04H 

0mi/0km 

0.5mi/0.8km 

1.2 mi/2.0km 

06H 

0.1mi/0.2km 

0.7mi/1.2km 

1.4mi/2.3km 

09H 

0.4mi/0.7km 

1.0mi/1.6km 

1.8 mi/3.0km 

13H 

1.4mi/2.3km 

2.0mi/3.3km 

2.8mi/4.7km 

31H 

4.4mi/7.3km 

5.0mi/8.3km 

5.8 mi/9.7km 

45H 

6.4mi/10.7km 

7.0mi/11.7km 

7.8mi/13.0km 

64H 

9.4mi/15.7km 

10.0mi/16.7km 

10.8mi/18.0km 

C8H 

9.4mi/32.3km 

20.0mi/33.3km 

20.8mi/34.7km 

FAH 

24.4mi/40.7km 

25.0mi/41.7km 

25.8mi/43.0km 

 

Содержание SEM2410























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды