Circontrol Raption 50 Series Скачать руководство пользователя страница 9

Страница: 9 / 168

So, hello!

Important safety instructions

• Read all the instructions before using

and configuring the Charge Point.

• Do not use the Charge Point for

anything other than electric vehicle
charging modes are expected in IEC
61851.

• Do not modify the Charge Point. If

modified, CIRCONTROL will reject all
responsibility and the warranty will
be void.

• Comply strictly with electrical safety

regulations according to your country.

• Do not make repairs or manipulations

with the unit energized.

• Only trained and qualified personnel

should have access to the electrical
parts inside the Charge Point.

• Check the installation annually by

qualified technician.

• Remove from service any item that

has a fault that could be dangerous
for users (broken connectors, caps
that don’t close...).

• Use only Circontrol supplied spare

parts.

• Do not use this product if the

enclosure or the EV connector is
broken, cracked, open, or shows any
ot

her indication of damage.

• Adaptors

or conversion adapters and

cord extensions set are NOT allowed
to be used.

Read carefully all the instructions before using the

Charge Point.

Содержание Raption 50 Series









































































































































































Результаты поиска

Содержание Raption 50 Series

Отзывы:

Похожие инструкции для Raption 50 Series

Бренды по названию

Популярные бренды

Circontrol Raption 50 Series, Руководство пользователя

Результаты поиска

Содержание Raption 50 Series

Отзывы:

Похожие инструкции для Raption 50 Series

Бренды по названию

Популярные бренды