Circontrol Raption 50 Series Скачать руководство пользователя страница 113

Страница: 113 / 168

109

Checkup

After applying new settings, please go to next URL from Charge Point in order to
check properly connection from the integration chosen:

http://

/services/cpi/log?app=ocpp1.5

‘CB boot notification: success’

appears then Charge Point is properly connected

to the back-end.

Otherwise, if the message shown is

‘Registering CB in the CS: failed’

then check

following items:

- Backend URL. Case sensitive. Check all the URL is correct.

- Charge Point ID. Case sensitive. Check if the name entered is same as backend
expects to receive.

- Connectivity. Check if modem is power up and connected to the HMI screen. Ask
to the backend provider if any request has been received from the charge point
(BootNotification, StatusNotification or HeartBeat) after upgrading.

Look especially for the following messages:

Содержание Raption 50 Series









































































































































































Результаты поиска

Содержание Raption 50 Series

Отзывы:

Похожие инструкции для Raption 50 Series

Бренды по названию

Популярные бренды

Circontrol Raption 50 Series, Руководство пользователя

Результаты поиска

Содержание Raption 50 Series

Отзывы:

Похожие инструкции для Raption 50 Series

Бренды по названию

Популярные бренды