CID TRBC162672 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

Xtreme Tree Reaper Brush Cutter

May 2022

32

4.0 Maintenance Overview

The maintenance procedures described in this manual should only be carried out by

qualified mechanics who have been trained to repair this machine.

Some procedures require special tools and skills to complete. DO NOT attempt to repair or

perform service work on this machine unless you have the skills and tools to do so. Contact

your local dealer for maintenance and repair services.

Improper maintenance or modifications to the design or performance of this machine

will void the warranty.

Obey the following safety instructions when servicing or repairing this machine.

Wear proper Personal Protective Equipment (PPE) while working on this machine,

which may include safety glasses, hard hats, steel toe boots, gloves, etc.

Wear a welding helmet when welding to protect your eyes, face and neck from flash

burn, ultra-violet radiation and heat.

Ensure all jack stands, lifts and hoists are in good working condtion and have the rated

load capacity to support the load.

Contact your dealer before performing any type of welding repair to this cutter, as this may

void warranty.

All authorized welding repairs must be performed by qualified welders in accordance to the

American Welding Society (AWS) standards. Welding procedures performed by unqualified

welders may deem this cutter unsafe to operate.

Welding Repairs

Parts

Only use genuine CID OEM replacement parts on this machine. CID will not be liable

for any damages or injuries caused by the use of after market parts on this machine.

«
...
30
31
32
33
34
...
»

Содержание TRBC162672





































































Отзывы:

Нет отзывов

Похожие инструкции для TRBC162672

Бренд: Power Fist Страницы: 16

535 Manual Chuck

Бренд: RIDGID Страницы: 17

Бренд: CRAIN Страницы: 2

Бренд: Hyd-Mech Страницы: 136

PAPER ROLL CUTTER

Бренд: DIY CREW Страницы: 3

Бренд: Kaiser Страницы: 2

Бренд: Logan Graphic Products Страницы: 4

Бренд: X4TOOLS Страницы: 12

Бренд: ES Страницы: 2

Бренд: Maruyama Страницы: 16

Бренд: Maruyama Страницы: 24

Бренд: Maruyama Страницы: 24

Бренд: Maruyama Страницы: 36

Бренд: WilTec Страницы: 28

Бренд: Olympia Tools Страницы: 2

Бренд: RSI Страницы: 12

Бренд: Royal Catering Страницы: 39

Бренд: Leigh Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды