background image

12 - OPTIONS

12.2.3.2 - Installation and operation of the heat recovery with partial heat recovery option 

The units with the desuperheater option are supplied with one plate heat exchanger per refrigerant circuit.
When installing the unit, the heat recovery plate heat exchangers must be insulated and protected against frost if required.
Refer to the main diagram below for the main components or functions associated with a unit with desuperheater option in a 

standard system.

Main diagram of the partial heat recovery option in a standard system

Heating mode

Cooling mode

AQUACIAT

POWER

 ILD ST/HE unit with desuperheater option without hydraulic model

Limit between the AQUACIAT

POWER

 ILD ST/HE unit and the system

Typical installation

Legend:

Components of the AQUACIAT

POWER

 ILD unit

1-  Water-cooled heat exchanger

2-   Compressor

3- Desuperheater

4-  Air condenser (coils)

5-  Expansion valve (EXV)

6-  Accessory for limitation of damage in the event of a fire (valve)

7-  Electric heater for protecting the desuperheater from freezing (not provided)

8-  Insulation for the desuperheater (not supplied)

9-  Electrical box for the unit

10-  Heating/cooling cycle four-way reversing valve

11-  Water inlet on the desuperheater

12-  Water outlet on the desuperheater

13-  Water heat exchanger water inlet

14-  Water heat exchanger water outlet

15-  Unit with desuperheater option without hydronic module

16-  System heat load

17-  Limit between the AQUACIAT

POWER

 ILD ST/HE unit and the standard system

System components (installation example)

20-  Pump (hydronic circuit for the desuperheater loop)

21-  Shut-off valve

22-  Desuperheater water flow rate control and balancing valve

23-  Accessory for limitation of damage in the event of a fire (valve)

24-  Expansion tank

25-  Charge or drain valve

26-  Air bleed

27-  Coil heat exchanger or plate heat exchanger

28-  Pressure gauge

29-  Flow rate sensor

30-  Pump (sanitary hot water circuit)

31-  Three-way controller

32-  Filter to protect the pump and the desuperheaters

33-  Municipal water inlet

34-  Domestic hot water outlet

AQUACIAT

POWER

 ILD 

EN-56  

Содержание AQUACIAT POWER ILD Series









































































Отзывы: