Chungho Super Iguassu ICE 900 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

Chungho Super Iguassu ICE 900 Скачать руководство пользователя страница 21

1

2

21

Ice Making Function Setting

Touch CONST button for over 10 seconds.

*As pressing the button, continuous water dispenser function is automatically set after

2seconds and Ice making function setting operates in 10 seconds. Continuous water

dispenser function automatically is released after 5 seconds.

ICE LED (Red) is turned on as the ice making function is set.

(Setting sound: Ding~ding~ding~)

1

2

Ice Making Function Release

Touch CONST button for over 10 seconds.

Ice Lamp (Red) is turned off and the ice making function is released.

(Setting sound: Ding~ding~ding~)

* When it is released, remained ice is dispensed until the ice storage house is being emptied.

But ice-making function is disabled.

HOT(hot water) Operation Setting

If hot water operation display LED is turned on by touching HOT/ECONO(hot
water operation/power saving selection) touch sensor button, the hot water
system will operate.

*Hot water system is operated by a detection sensor which automatically detects the tempera-

ture inside of the hot water tank.

HOT(hot water) Operation Release

If the hot water operation display LED is turned off by touching HOT/
ECONO(hot water operation/power saving selection) touch sensor button,
then the hot water system stops.

Pr

oduct

Usa

ge

EC

LOCK

HOT

IC

CO

ECO

«
...
19
20
21
22
23
...
»

Содержание Super Iguassu ICE 900

























































Отзывы:

Нет отзывов