Christini AWD 450DS Скачать руководство пользователя страница 41

Страница: 41 / 118

Page 40

Note: Before performing this test, make sure the AWD Clutch is set
correctly.

•

Place the bike on a stand and make sure that the wheels are not
touching the ground.

•

Turn the AWD switch to the on position and check to make sure
the AWD is engaged.

•

Center the handlebars.

•

Hold down the front and rear brakes.

•

Turn handlebars to the left and back to center. There should be
steering resistance from the AWD system when this is performed.

•

Release brakes and center handlebars.

•

Hold down front and rear brakes again and turn handlebars to the
right and back to center. There should be steering resistance
from the AWD system.

•

If no resistance is felt, or there is only resistance in one direction,
check the front wheel to ensure the sprag bearings are not slip-
ping or damaged. See “Front Wheel Service” section.

Front Wheel Sprag Test

Содержание AWD 450DS























































































































Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды

Christini AWD 450DS, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды