Christini AWD 450DS Скачать руководство пользователя страница 26

Страница: 26 / 118

Page 25

Maintenance

ENGINE IDLE SPEED

The engine must be warm for an accurate idle inspection and adjustment. Ten
minutes of stop and go riding is sufficient.

•

Warm up the engine, shift the transmission into neutral and hold the mo-
torcycle upright.

•

Turn the throttle stop screw to obtain the specified idle speed.

IDLE SPEED: 1,800+100 rpm

ENGINE OIL / OIL FILTER

OIL LEVEL INSPECTION

•

Run the engine at idle speed for 3 minutes, then stop it for 3 Minutes.

•

Support the motorcycle in an upright position on a level surface.

•

Remove the oil filter cap/dipstick and wipe the oil with clean cloth.

•

Insert the dipstick without screw in, take it out and check the oil level.

•

If the oil level is lower or near the lower level line on the stick, add recom-
mended oil to the upper level line through the hole.

•

Reinstall the engine oil filter cap

(other viscosities shown in the chart may be used when the average temperature in your
riding area is within the indicated range)

RECOMMENDED ENGINE OIL:

HP4M (with molybdenum additives) 4-stroke oil , or equivalent motor oil

API service classification : SG or higher

JASO T 903 STANDARD :MA or MB, viscosity : SEA 10W -40

OIL CAPACITY

0.67liter at draining

0.70liter at oil filter change

Содержание AWD 450DS























































































































Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды

Christini AWD 450DS, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды