Christini AWD 450DS Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 118

background image

Page 18

Maintenance

AWD Lever

FREE PLAY: 2-3mm(1/8-3/16in)

•

Check for smooth Lever operation and lubricate the cable if required.

•

Inspect the cable for cracks which could allow moisture to enter. Replace
the cable if necessary.

•

Measure the lever free play at the lever end. Lever free play can be ad-
justed. Adjust the free play by loosening the lock nut and turning the ad-
juster.

•

Tighten the lock nut. Reinstall the dust cover. Recheck the free play at the
lever.

AIR FILTER

•

Loosen the air cleaner retaining bolt. Remove the air filter.

•

Remove the air filter from the holder.

•

Thoroughly wash the air filter in clean non-flammable or high flash-point
cleaning solvent. Then wash the element again in a solution of hot water
and dishwashing liquid soap. Clean the inside of the air cleaner housing.

•

After cleaning, be sure there is no dirt or sand trapped between the inner
and outer layer of the cleaner. Wash again if necessary.

•

Allow the air cleaner to dry thoroughly. After drying, soak the air filter in
clean Foam Filter Oil or an equivalent.

•

Apply air filter oil to the entire surface of the air filter and rub it with both
hands to saturate the element with oil.

•

Gently squeeze out excess oil. It is important not to over oil or under oil
the element. Apply a thin coat of grease or an equivalent to the sealing
surface.

•

Assemble the air filter and the holder .Slip the air cleaner retaining bolt
through the assembly. Tighten the retaining bolt securely.

NOTICE: If the air filter assembly is not installed correctly ,dirt and dust may
enter the engine resulting in wear of the piston ring and cylinder.

CRANKCASE BREATHER

•

Remove the breather hose drain plug, then drain any fluids or dirt from
the hose into a proper container. Reinstall the drain plug.

«
...
17
18
19
20
21
...
»

Содержание AWD 450DS























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 450DS

Бренд: UNIT 1 Страницы: 23

Бренд: Kabuto Страницы: 16

Бренд: ICON Страницы: 2

Power commander GSXR750

Бренд: Dynojet Страницы: 4

Бренд: R&G Страницы: 10

Бренд: R&G Страницы: 21

Бренд: hepco & becker Страницы: 2

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Бренд: BSA Страницы: 120

Бренд: Denali Страницы: 2

Multistrada 620

Бренд: Ducati Страницы: 382

Бренд: R&G Страницы: 13

Бренд: R&G Страницы: 9

Бренд: Royal Enfield Страницы: 110

Бренд: Shad Страницы: 2

SYM JOYMAX 125 GTS '13

Бренд: Shad Страницы: 2

TOPMASTER Y0RX53ST

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 3

Бренд: Shad Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды