Christini AWD 450DS Скачать руководство пользователя страница 3

Страница: 3 / 118

Page 2

Introduction

Congratulations for making the choice to become and AWD rider!

The instructions in this book will provide a simple and understandable guide to your motorcycle’s operation and

maintenance.

Whenever you see the symbols shown below, heed their instructions!

Always follow safe operating and maintenance practices.

If improperly conducted, the sport has the potential to cause environmental problems as well as conflicts with other

people. Responsible use of your motorcycle will ensure that these problems and conflicts do not occur.

TO PROTECT THE FUTURE OF YOUR SPORT, MAKE SURE YOU USE YOUR BIKE LEGALLY, SHOW

CONCERN FOR THE ENVIRONMENT, AND RESPECT THE RIGHTS OF OTHER PEOPLE.

This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when

resold or otherwise transferred to a new owner or operator.

We reserve the right to amend this motorcycle service manual due to periodic improvements and upgrades.

WARNING

This warning symbol identifies special instructions or procedures which, if not correctly followed, could result in personal
injury, or loss of life.

CAUTION

This caution symbol identifies special instructions or procedures which, if not strictly observed, could result in
damage to or destruction of equipment.

NOTE

This note symbol indicates points of particular interest for more efficient and convenient operation.

Содержание AWD 450DS























































































































Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды

Christini AWD 450DS, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450DS

Отзывы:

Похожие инструкции для AWD 450DS

Бренды по названию

Популярные бренды